MCM Travertine Stone Installation Guide | Professional Support

Before diving in, gather these essentials to avoid mid-project delays:

• Measuring tools: Laser level, tape measure (5m+), square ruler
• Cutting equipment: Diamond-tipped saw (for MCM big slab board series ), utility knife (for flexible stone)
• Adhesives: Polymer-modified mortar (recommended for heavy panels), contact adhesive (for flexible stone cladding panels )
• Surface prep: Sanding block, wire brush, vacuum cleaner
• Safety gear: Gloves, goggles, dust mask (especially when cutting fair-faced concrete panels)

Each MCM product has its own personality—take time to get to know yours:

For MCM big slab board series (1200x2400mm+): Check edges for chips, as large panels are more vulnerable to transport damage. Lay them flat on a clean surface and inspect for consistent thickness—variations beyond 1mm may affect alignment.

For MCM flexible stone : Gently bend a corner (15-20° angle) to test flexibility. High-quality flexible stone should spring back without cracks, ensuring it can hug curved surfaces like column wraps or archways.

For travertine (starry green) : Examine the natural hole pattern—these "starry" pockets are part of its charm, but excessive breakage around holes may weaken the panel. A quick water test (dab a damp cloth) will reveal the true depth of its green hue, helping you plan layout for color consistency.

MCM materials thrive on stable, clean substrates. Here's how to prep different bases:

Fair-faced concrete walls: Fill cracks wider than 2mm with cementitious filler. Sand rough spots until the surface is smooth to the touch—any bumps will show through thin MCM panels. Wipe away dust with a damp cloth and let dry completely (minimum 24 hours).

Existing tile or masonry: Ensure no loose tiles or mortar. Use a wire brush to remove efflorescence (white salt deposits) and apply a bonding primer if the surface is overly smooth.

Wooden substrates (for interior projects): Cover with moisture-resistant drywall first—MCM needs a non-organic base to prevent warping over time.

These large-format panels (up to 3600x1200mm) make a bold statement, but their size demands teamwork and precision. Here's how to handle them:

Step 1: Mark your layout Use a laser level to snap vertical and horizontal reference lines. For exterior walls, include a 5mm expansion gap at the top and bottom to accommodate thermal movement.

Step 2: Apply adhesive strategically For slabs over 2m², use the "dot-and-comb" method: apply 10-12 dollops (50mm diameter) of mortar across the back, then comb a thin layer (3mm) between them. This ensures full contact without excess squeeze-out.

Step 3: Lift with care Two people per slab is a must. Use suction cups with rubber pads to avoid surface scratches. Align the top edge with your reference line and gently lower—avoid sliding, which can disturb the adhesive bed.

Step 4: Secure and clean Tap the surface with a rubber mallet (cover with a cloth to prevent dents) to set the slab. Remove excess mortar immediately with a damp sponge—dried mortar can stain the panel's finish.

The magic of MCM flexible stone lies in its ability to conform to curves, making it perfect for wave panels, circular columns, or organic-shaped feature walls. Here's how to master its unique properties:

Step 1: Test the bend radius Different designs have different limits: wave panels handle 500mm radii easily, while thinner mosaic sheets can wrap around 100mm pipes. Do a dry fit first to avoid creasing.

Step 2: Use contact adhesive for curves On flat surfaces, standard mortar works, but curved areas need contact adhesive. Apply a thin, even layer to both the back of the flexible stone and the substrate. Let it tack up (15-20 minutes) before pressing—this creates an instant bond.

Step 3: Work in sections For large areas like a curved lobby wall, cut the flexible stone into 600mm-wide strips. Start at the top and smooth downward with a plastic trowel, pushing out air bubbles from the center to the edges.

Step 4: Finish the edges Flexible stone can be trimmed with scissors or a utility knife. For exposed edges (like around windows), use a matching color sealant to create a seamless look.

COLORIA's MCM 3D printing series pushes boundaries with custom geometries—think interlocking tiles,, or parametric patterns. Installing these prefabricated art pieces requires a methodical approach:

Step 1: Follow the sequence Each 3D-printed panel is numbered to ensure the design aligns correctly. Lay them out on the floor first to confirm the pattern flows as intended.

Step 2: Reinforce for weight Larger 3D pieces may need mechanical support. Use stainless steel brackets (painted to match) at stress points, hidden behind the panel's raised details.

Step 3: Grout with care The intricate textures of 3D-printed MCM trap grout easily. Use a foam brush to apply grout, then wipe with a damp cloth in the direction of the texture to preserve details.